Self-resetting PPTC (Polymer Positive Temperature Coefficient) devices are widely used in infotainment systems to protect precision electronic components and peripherals. In applications where the self-recovery function is not desirable or practical, a chip surface mount fuse is typically used.
This article refers to the address: http://
Infotainment devices are also susceptible to damage due to excessive transient voltages, including the working environment in which they are located and the electrostatic discharge (ESD) pulses generated by peripheral devices. ESD protection devices, metal oxide varistor (MOV) and Zener diodes are often used to protect automotive electronic devices such as antennas, backlight heaters, batteries, buttons, printed circuits on circuit boards, CD/DVD players, data lines Ports, hard drives, and input/output ports and touch screens.
Design considerations for automotive circuit protection devices
# PPTC overcurrent / overheat protection
The popular PPTC device has a self-resetting function that can be mounted in an easily accessible location in a car. It has a wide range of products with different electrical properties and sizes to facilitate a variety of precise protection designs. When selecting a PPTC device, the main consideration is that the device's holding current rating is matched to the primary current of the device during normal operation.
# ESD protection device
High-speed input/output ports require the use of small-capacitance ESD protection devices to keep signal quality as low as possible. The device chosen should be suitable for high-speed data transmission lines and radio frequency data lines, capable of withstanding numerous ESD transients. To meet the requirements of RoHS and IEC61000-4-2, the capacitance is small, the trigger voltage is low, and the response time is short. These are also important features of ESD protection devices.
# Surface Mount Fuse
Surface mount fuses with large currents and small sizes have both fast and slow fuses, and their fuse characteristics should be clean, including the fuse process should be carried out inside the package. Their ability to suppress arcing should be good and able to withstand shock and vibration.
# 金属氧化å˜å˜å™¨
Metal oxide varistors (MOVs) are available in a variety of diameters and voltage ranges. MOV devices can flow a large amount of current and absorb a large amount of energy to achieve overvoltage protection. When selecting MOV, it is based on the clamp voltage level (suppressed voltage rating) and response time.
DC power port protection
The car power bus is very dirty, which is known to everyone. The car's power supply is rated at 12V, but will vary from 8V to 16V during normal operation. Also, the current of the battery will exceed 100 amps, and it will be interrupted by the action of the relay or the fuse is blown. Therefore, a large induced voltage spike is generated on the power bus, and the voltage is increased by more than 5 times.
During the operation of the car's power supply, it may be damaged by a battery connection error or when it is connected to a battery with twice the voltage (24 volts) when the dual battery is started. There is a situation called "load dumping" which can generate very high voltages on the power bus. A typical third-party power converter will filter it out, but tests by Tyco Electronics show that the ability of these power converters to reject transient voltages varies greatly. Devices that typically charge the USB interface are generally not designed for this type of voltage fluctuation and therefore require overvoltage protection.
The demand for overcurrent and overvoltage protection in portable devices that are being recharged in the car is growing, and Tyco Electronics' new PolyZen® devices are able to meet its needs. When used with a Zener diode-like protection device, this device has a synergistic protection against high power fault conditions.
Figure 1: PolyZen devices protect the input power, DC power, and output power conditioning circuitry of automotive peripherals.
As shown in Figure 1, the miniature PolyZen device contains a stable Zener diode and a non-linear resistive PPTC layer. The Zener diode precisely clamps the voltage, and the resistive PPTC layer responds to the diode's heating or overcurrent events, transitioning from a low resistance state to a high resistance state.
PolyZen devices are particularly effective for clamping and smoothing inductive voltage spikes. In the presence of an inductive spike, the Zener diode bypasses the current to ground until the voltage drops to the normal operating range. In the case of a supply voltage error, the PolyZen device clamps the voltage and bypasses excessive current to ground to prevent power supply errors. The voltage and current response characteristics of PolyZen devices are relatively flat, which helps clamp the output voltage, even if the input voltage and supply current vary.
Because the current can be very large in automotive applications, be careful and ensure proper protection. For the selected device, check its IFLT maximum and Vout peak to ensure that the device provides the required protection.
PCB board for protecting electronic modules
The market demands more electronics and more internal space. In response to this demand, automakers are putting more circuits into smaller packages. In order to provide more and more functions and connections with smaller and denser printed circuit board areas, the printed line width on the board must be reduced.
Many of these control modules are "black boxes" that are now used to control an increasing number of high-power accessories, such as power windows, power seat adjustments, remote door locks, and radios and GPS antennas. Because the power supply for these accessories is provided by a circuit with a large current, the possibility of burnout increases because the printed circuit on the printed circuit board is very thin and a large current flows. This situation is possible. For example, if a power ground is disconnected from the load, its current will flow through a small printed line on the board, and the current in this trace will increase.
The printed lines on the printed circuit board function to carry current from one place to another. The current that can flow through each trace depends on its cross-sectional area. The maximum current is the heat generated by the I2R power dissipation that does not blow it off. Even if it has not melted, it may be hot enough to damage the printed circuit board or damage some of the components mounted on it.
Self-resetting PPTC devices are often used to protect these tiny printed lines on the board because such devices can quickly and efficiently limit current to safe values ​​and are small enough to fit directly onto the board. Using this technology, each individual power supply circuit in the module can be protected with a PPTC device, limiting the current to a safe value without blowing it. The fuse and PolySwitch devices are compared in Figures 2 and 3. Here we assume that the board designer sets the maximum temperature of the printed line at 100 °C. Therefore, as the temperature of the printed line approaches 100 ° C, the current that can flow over it becomes smaller and smaller.
The example shown in Figure 2 is a 1 oz (35 μm), 100 mil (2.5 mm) printed line that is protected with a plug-in PolySwitch® device AGR500. In Figure 3, the width of the trace is reduced to 20 mils (0.5 mm) and protected with a PolySwitch series surface mount device ASMD150.
Figure 2: The performance of the fuse and PolySwitch device AGR500 is compared.
Figure 3: The performance of the fuse and PolySwitch device ASMD150 is compared.
It must be noted that the trigger current of the PPTC device follows the current on the trace over the entire temperature range. In both cases, even if a fuse can be used, the closest fuse can't protect it when the car is above the useful standard temperature.
PPTC circuit protection devices are widely used as a practical, cost-effective solution for overcurrent and/or overtemperature protection in electronic modules. This device is often used to limit current in GPS, DVD or radio and telematics boards.
summary
There are now a variety of innovative circuit protection solutions, with a variety of sizes and a variety of soldering end products, which can help automakers and portable equipment manufacturers meet the stringent requirements of automobiles, improve equipment reliability, and enhance end-users. Convenience and satisfaction. With overcurrent, overvoltage, and ESD synergy, you can reduce component count and increase the efficiency and reliability of your electronic components and networks.
USB 2.0 3.0 Flash Pen Drives FLASH Memory Pendrive USB Stick
1.What is the write speed ?
our USB 2.0 flash drive write speed is 5M/S - 10M/S or you will lucky to get 11M+.
Different device and different platform will affect a lot on the speed testing.
if you want to save 1GB film in our USB flash drive,that you need the time is 2 mins,it save your time.
2.Why the USB flash drive real capacity is not correct capacity?
Flash memory vendors are using decimal arithmetic:1MB = 1000KB,1G = 1000MB
calculated, the operating system using binary arithmetic:1MB = 1024KB,1GB = 1024MB;
so there are some differences between display capacity and nominal capacity of flash memory product
About capacity:
4GB=approximately 3.5GB-3.7GB
8GB=approximately 7.4GB-7.8GB
16GB=approximately 14GB-15GB
32GB=approximately 28GB-30GB
64GB=approximately 58GB-59GB
128GB=approximately 115GB-120GB
3.Note for the delivery (Please read before ordering ):
Value is less than 15$ Mode of transport = China Post, E-Packet Plus & Alibaba 3C Economic Package
1.Every shipping mode is sent with a tracking number, but there are several Countries or Areas can only be tracked before leave China.
2.The shipping leadtime to most of the countries, normal is 15 - 45 working days( Russia and Brazil 30- 60 working days)
3. If your Confirmation Time is coming,and still not do receive the goods,please contact with us to extend the delivery date and extend the delivery date at yourside at the same time.
4. However, Please do trust us. You will get the package in time.
5. If your Items is not received in 60 days,we will 100% refund
6. Please do not open dispute within 60days,Thanks for your kind understanding.
Usb Flash Disk,Usb Drive,Flash Drive Usb,Metal Usb Stick, U disk
MICROBITS TECHNOLOGY LIMITED , https://www.microbitstrade.com